Casio GW-M5610LY-1 manual

Casio GW-M5610LY-1
(1)
  • Number of pages: 6
  • Filetype: PDF
  • Operation Guide 3159

    1
    MO1005-EA

    Getting Acquainted

    Congratulations upon your selection of this CASIO watch. To get the most out of your
    purchase, be sure to read this manual carefully.
    Keep the watch exposed to bright light
    The electricity generated by the solar cell of the watch is
    stored by a rechargeable battery. Leaving or using the
    watch where it is not exposed to light causes the battery
    to run down. Make sure the watch is exposed to light as
    much as possible.
    When you are not wearing the watch on your wrist,
    position the face so it is pointed at a source of bright
    light.
    You should try to keep the watch outside of your sleeve
    as much as possible. Charging is reduced significantly if
    the face is covered only partially.
    l
    l
    l
    l
    l
    l
    l
    l
    l
    l
    l

    Bright Light

    Solar cell

    All

    functions

    enabled

    LEVEL 1

    LEVEL 2

    LEVEL 3

    LEVEL 4

    Charge

    Rechargeable battery

    Bright Light

    Electrical

    energy

    Solar cell

    (Converts light to

    electrical power.)

    Battery charges in the light. Battery discharges in the dark.

    The watch continues to operate, even when it is not exposed to light. Leaving the
    watch in the dark can cause the battery to run down, which will result in some watch
    functions to be disabled. If the battery goes dead, you will have to re-configure watch
    settings after recharging. To ensure normal watch operation, be sure to keep it
    exposed to light as much as possible.

    LEVEL 1

    LEVEL 2

    LEVEL 3

    LEVEL 4

    Some or all

    functions

    disabled

    Dis-

    charge

    The actual level at which some functions are disabled depends on the watch model.
    Frequent display illumination can run down the battery quickly and require charging.
    The following guidelines give an idea of the charging time required to recover from a
    single illumination operation.

    Approximately 5 minutes exposure to bright sunlight coming in through a window

    Approximately about 8 hours exposure to indoor fluorescent lighting

    Be sure to read “Power Supply” for important information you need to know
    when exposing the watch to bright light.
    If the display of the watch is blank...
    If the display of the watch is blank, it means that the watch’s Power Saving function
    has turned off the display to conserve power.
    See “Power Saving Function” for more information.
    Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage
    or loss suffered by you or any third party arising through the use of this product or
    its malfunction.
    About This Manual
    Depending on the model of your watch, display text appears either as dark figures
    on a light background or light figures on a dark background. All sample displays in
    this manual are shown using dark figures on a light background.
    Button operations are indicated using the letters shown in the illustration.
    Each section of this manual provides you with the information you need to perform
    operations in each mode. Further details and technical information can be found in
    the “Reference” section.

    General Guide

    Press C to change from mode to mode.
    In any mode (except when a setting screen is on the display), press B to illuminate
    the display.
    Timekeeping Mode
    Press C.
    Countdown Timer Mode Stopwatch Mode
    Alarm Mode
    World Time Mode

    Radio-controlled Atomic Timekeeping

    This watch receives a time calibration signal and updates its time setting accordingly.
    This watch is designed to pick up the time calibration signals transmitted in Germany
    (Mainflingen), England (Anthorn), the United States (Fort Collins), China (Shangqiu),
    and Japan (Fukushima, Fukuoka/Saga).
    Current Time Setting
    This watch adjusts its time setting automatically in accordance with a time calibration
    signal. You also can perform a manual procedure to set the time and date, when
    necessary.
    The first thing you should do after purchasing this watch is to specify your
    Home City (the city where you normally will use the watch). For more
    information, see “To specify your Home City”.
    When using the watch outside the areas covered by the time signal transmitters, you
    will have to adjust the current time setting manually as required. See “Timekeeping”
    for more information about manual time settings.
    The U.S. time calibration signal can be picked up by the watch while in North
    America. The term “North America” in this manual refers to the area that consists of
    Canada, the continental United States, and Mexico.
    As of December 2009, China does not use Daylight Saving Time (DST). If China
    does go to the Daylight Saving Time system in the future, some functions of this
    watch may no longer operate correctly.
    Using this watch in a country covered by a time calibration that is different from the
    countries it supports may result in incorrect time indication due to local application of
    summer time, etc.

    To specify your Home City

    1. In the Timekeeping Mode, hold down A until the city
    code starts to flash, which indicates the setting screen.
    2. Press D (east) and B (west) to select the city code
    you want to use as your Home City.
    LIS, LON : Lisbon, London
    MAD, PAR, ROM, BER, STO : Madrid, Paris,
    Rome, Berlin, Stockholm
    ATH : Athens
    MOW : Moscow
    HKG, BJS, TPE : Hong Kong, Beijing, Taipei
    SEL, TYO : Seoul, Tokyo
    HNL : Honolulu
    ANC : Anchorage
    YVR, LAX: Vancouver, Los Angeles
    YEA, DEN
    : Edmonton, Denver
    MEX, CHI : Mexico City, Chicago
    MIA, YTO, NYC: Miami, Toronto, New York
    YHZ : Halifax
    YYT : St.Johns

    PM indicator

    l
    l
    l
    l
    l
    l
    l
    l
    l
    l
    l
    l
    l
    l
    l
    l
    l

    City code

    Hour : Minutes

    Seconds

    3. Press A to exit the setting screen.
    Normally, your watch should show the correct time as soon as you select your Home
    City code. If it does not, it should adjust automatically after the next auto receive
    operation (in the middle of the night). You also can perform manual receive or you
    can set the time manually.
    The watch will receive the time calibration signal automatically from the applicable
    transmitter (in the middle of the night) and update its settings accordingly. For
    information about the relationship between city codes and transmitters, see
    “Important!” under “Time Calibration Signal Reception” and “Transmitters”.
    See the maps under “Approximate Reception Ranges” for information about the
    reception ranges of the watch.
    You can disable time signal reception, if you want. See “To turn auto receive on and
    off” for more information.
    Under factory default settings, auto receive is turned off for all of the following city
    codes: MOW (Moscow), HNL (Honolulu), and ANC (Anchorage). For details about
    turning on auto receive for these city codes, see “To turn auto receive on and off”.
    Time Calibration Signal Reception
    There are two different methods you can use to receive the time calibration signal:
    auto receive and manual receive.
    Auto Receive
    With auto receive, the watch receives the time calibration signal automatically up to
    six times a day (five times a day for the Chinese calibration signal). When any auto
    receive is successful, the remaining auto receive operations are not performed. For
    more information, see “About Auto Receive”.
    Manual Receive
    Manual receive lets you start a time calibration receive operation with the press of a
    button. For more information, see “To perform manual receive”.
    Important!
    When getting ready to receive the time calibration signal, position the watch as
    shown in the nearby illustration, with its 12 o’clock side pointing towards a window.
    This watch is designed to receive a time calibration signal late at night. Because of
    this, you should place the watch near a window as shown in the illustration when you
    take it off at night. Make sure there are no metal objects nearby.
    12 o’clock
    or
    Make sure the watch is facing the right way.
Casio GW-M5610LY-1

Got a question?

Number of questions: 0

Do you have a question about the Casio GW-M5610LY-1 or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Casio GW-M5610LY-1 owners to properly answer your question.

View the manual for the Casio GW-M5610LY-1 here, for free. This user manual comes under the category Watches and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Casio GW-M5610LY-1? Ask your question here

Casio GW-M5610LY-1 specifications

General
Brand Casio
Model GW-M5610LY-1
Product Watch
Language English
Filetype PDF
Technical details
Mechanism type Tough Solar
Chronograph -
Chronometer -
Watch dial type LCD dial
Waterproof
Water resistant pressure 20 ATM
Water resistant depth 200 m
Shockproof
Stopwatch
Snooze function
Timer 1h
Alarm function
Calendar
Countdown timer
Certification -
Watch type Wrist watch
Calendar type Day
Design
Watch case material Resin
Housing colour Black,Green
Band material -
Band main colour Black
Watch glass type Mineral
Case shape Rectangular
Watch dial main colour Black
Product design -
Power
Battery level indicator
Weight & dimensions
Width 43.2 mm
Depth 12.7 mm
Height 46.7 mm
Weight 52 g
show more

Frequently asked questions

Below, you will find the most frequently asked questions about the Casio GW-M5610LY-1.

Is your question not listed? Ask your question here