Panduit CT-160 manual

Panduit CT-160
(1)
  • Number of pages: 2
  • Filetype: PDF
  • CAUTION:

    Verify power is “OFF” before working on wiring with this tool.
    The plastic grips are for the user’s comfort,
    and are not intended to insulate against electrical shock
    while working on live electrical circuits.

    CT-160

    CRIMPING TOOL

    OPERATION INSTRUCTIONS
    1
    0
    -3
    2
    .
    8
    0
    1
    .
    0
    1
    .
    3
    1
    .
    6
    2
    .
    0
    2
    .
    6
    MM
    CUT
    COPPER
    ONL
    Y
    2
    2
    2
    0
    1
    8
    1
    6
    1
    4
    1
    2
    1
    0
    AW
    G
    8
    -
    32
    6
    -
    32
    M
    5
    M
    4
    M
    3
    .
    5
    I
    N
    S
    U
    L
    A
    T
    I
    O
    N
    AU
    TO
    7
    -
    8
    MM
    I
    N
    S
    I
    N
    S
    N
    O
    N
    I
    N
    S
    N
    O
    N
    I
    N
    S
    1
    2
    -1
    0
    2
    2
    -1
    4
    1
    2
    -1
    0
    2
    2
    -1
    4
    CLOSE
    HERE
    I
    N
    S
    E
    R
    T
    S
    C
    R
    E
    W
    S
    T
    H
    I
    S
    S
    I
    D
    E

    CT-160

    NON-INSULATED BUTT SPLICE
    INSTRUCTIONS
    1. Insert stripped wire into end of the butt
    splice to internal wire stop. (See product
    packaging for proper strip lengths.)
    2. Locate butt splice in proper non-
    insulated crimp pocket.
    3. Position crimp pocket on the center of
    the metal barrel half with wire inserted.
    4. Squeeze handles firmly.
    5. Repeat for other end of butt splice.
    Page: 1 of 2
    PA24427A01
    REV.: 02 5-2014
    OPERATION INSTRUCTIONS

    © Panduit Corp. 2014

    CT-160

    For Technical Support:
    1-888-506-5400, ext. 83255
    E-mail:
    See product packaging or contact Customer Service for
    UL/CSA approved tooling/product combinations.
    INSULATED BUTT SPLICE
    INSTRUCTIONS
    1. Insert stripped wire into end of the butt
    splice to internal wire stop. (See product
    packaging for proper strip lengths.)
    2. Locate butt splice in proper insulated
    crimp pocket.
    3. Position crimp pocket on the center of
    the metal barrel half with wire inserted.
    4. Squeeze handles firmly.
    5. Close insulation if desired.
    6. Repeat for other end of butt splice.
    WIRE STRIPPER for removing plastic or
    rubber wire insulation. Strip length should
    allow a minimum of 1/32” of conductor to
    extend beyond terminal barrel.
    WIRE CUTTER for No. 10 AWG and
    smaller copper wire.
    CUTTERS for machine screws of sizes
    shown. Open handles, thread screw in this
    side. Close handles to cut screw.
    CRIMPING POCKETS for Pan-Term non-
    insulated and insulated terminals,
    disconnects, splices and wire joints on No.
    22 to 10 AWG stranded wire. See product
    packaging for proper crimping pockets.
    This tool is made of hardened steel and is
    protected with a light coat of oil.
    NON-INSULATED AND INSULATED
    PARALLEL SPLICE INSTRUCTIONS
    1. Insert stripped wire into each end of the
    parallel splice. (See product packaging
    for proper strip lengths.)
    2. Locate parallel splice in proper crimp
    pocket.
    3. Position crimp pocket on the center of
    the metal barrel.
    4. Squeeze handles firmly.

    CRIMP POCKET

    CRIMP POCKET

    CRIMP POCKET

    CRIMP POCKET

    NON-INSULATED

    INSULATED

    www.panduit.com
Panduit CT-160

Got a question?

Number of questions: 0

Do you have a question about the Panduit CT-160 or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Panduit CT-160 owners to properly answer your question.

View the manual for the Panduit CT-160 here, for free. This user manual comes under the category Tongs and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Panduit CT-160? Ask your question here

Panduit CT-160 specifications

General
Brand Panduit
Model CT-160
Product Tongs
Language English
Filetype PDF
Technical details
Type Crimping tool
Product colour Black,Green