Sony SNC-EB632R manual

Sony SNC-EB632R
  • Number of pages: 2
  • Filetype: PDF
85.7 (3
Hole for connecting cables ø40 (1
Horizontal makerHole for installing the standUnit: mm (inches)83.7 (3
Vertical marker83.7 (3
85.7 (3
CeilingWire rope (supplied)Camera unitmounting screw(not supplied) (4)
Overlap at least half of its width
10 (
) 10 (
4-538-945-11(1)© 2014 Sony Corporation Printed in China

Network Camera


Installation ManualBefore operating the unit, please read this manual thoroughly and retain it for future reference.
About the Manuals
Installation Manual (this document)This Installation Manual describes the names and functions of parts and controls of the Network Camera, gives connection examples and explains how to set up the camera. Be sure to read the Installation Manual before operating.SNC easy IP setup Guide (stored in the CD-ROM) User’s Guide/Application Guide (Web)The User’s Guide describes how to set up the camera and how to control the camera via a Web browser.After installing and connecting the camera correctly, operate referring to this User’s Guide.
Using the Software
The supplied CD-ROM includes the setup program for assigning an IP address. The information for how to set up an IP address is also included in the disc in PDF format.User’s Guide and Application Guide can be downloaded from the disc, or the following URL:
Using the CD-ROM manual
The manual can be read on a computer with Adobe Reader installed.You can download Adobe Reader free from the Adobe website.
1 Open the index.html file in the CD-ROM.
2 Select and click on the manual that you want to read.
Note If you have lost or damaged the CD-ROM, you can purchase a new one from your Sony dealer or Sony service counter.Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in the United States and/or other countries.
Assigning the IP address
Assign the IP address using the setup program in the supplied CD-ROM.For details on how to set up the IP address, see SNC easy IP Setup Guide.
Location and Function of Part
Wire ropeWhen installing the camera on the ceiling or the wall, make sure to attach the supplied wire rope.
Sun shield nut
Front cover
Ground wireGround the camera when you install it.
LAN cable (RJ-45)Connect this cable to a hub or computer on the 10BASE-T or 100BASE-TX network using a commercially available network cable (UTP, category 5).
Take care not to trap the cables between the camera and the ceiling or the wall. If the cable is trapped, it may cause a fire or electric shock due to breaking.
Sun shieldThe sun shield can be adjusted horizontally up to 26 mm (1
/8 inches), as required.
Front cover screw (four positions)
POWER indicator (Green)When the power is supplied to the camera, the camera starts checking the system. If the system is normal, this indicator lights up.
HEATER indicator (Green)The indicator lights up in green when the built-in heater is working normally.
NETWORK indicator (Green/Orange)The indicator lights up or flashes when the camera is connected to the network. The indicator is off when the camera is not connected to the network.
Reset switchTo reset the camera to the factory default settings, hold down this switch with a point and supply the power to the camera.
VIDEO (NTSC/PAL) switch (Initial setting: NTSC)Switches the video output.After setting the switch, reboot the camera unit.
ZOOM/FOCUS switchUse this switch to adjust lens’ zoom and focus. Slide the switch lever to select the desired function.[W] WIDE: Zoom out[T] TELE: Zoom in[N] NEAR: Focus on a nearby subject[F] FAR: Focus on a distant subjectHold down the center of the ZOOM/FOCUS switch for a moment to focus automatically.
MONITOR output jackConnect this jack to a video input connector of a video monitor. You can adjust the camera or lens while looking at the image on the video monitor. After adjusting the camera or lens, disconnect the cable.
Base stand
Base screw (two positions)
TOP mark
Arm screw
Rating labelShows the name of this camera and its electric rating.
Water drainWhen installing the unit on a wall, make sure this water drain is not sealed.
WARNINGIf you attach the camera in the height such as the wall or the ceiling, etc.,
entrust the installation to an experienced contractor or installer.If you install the camera at a height, ensure that the installation location and
its material are strong enough to withstand a weight of 15 kg (33 lb 11 oz) or more, and then install the camera securely. If the ceiling is not strong enough, the camera may fall and cause serious injury.Do not pull on any cables forcefully, as a connection may become loose.
To prevent the camera from falling, make sure to attach the supplied wire rope.
If you attach the camera to the ceiling, check periodically, at least once a year,
to ensure that the connection has not loosened. If conditions warrant, make this periodic check more frequently.
Deciding the Installation Location of the Camera
After deciding the direction in which the camera will shoot, make the required hole (ø40 mm (1
/40 inches)) for the connecting cables using the supplied template. Then decide the four mounting hole positions to install the bracket.Mounting screwsThe camera stand is provided with four ø4.5 mm (
/16 inches) mounting holes. Install the camera stand on a ceiling or wall with screws through four mounting holes: The required mounting screws differ depending on the installation location and its material. (Mounting screws are not supplied.)Steel wall or ceiling: Use M4 bolts and nuts.Wooden wall or ceiling: Use M4 tapping screws. The panel thickness must be 15 mm (
/8 inches) or more.Concrete wall: Use anchors, bolts and plugs suitable for concrete walls.Junction box: Use screws to match the holes on the junction box.WARNINGThe required mounting screws differ depending on the installation location and its material. If you do not secure the camera with the appropriate mounting screws, the camera may fall off.
Installing the Camera
Pass the LAN cable and the ground wire through the hole for connecting cables made at the installing surface.
2 Fix the wire rope to the wall or ceiling.
3 Install the camera on the wall or ceiling.
The remaining cable can be incorporated in the space between the base stand and the mounting surface. (
Insert the four screws in the screw holes on the camera stand, and then tighten the screws to attach the camera.When installing the camera on the wall, be sure the TOP mark on the camera stand is at the top.Refer to “Mounting screws” in section D for screw to be used.NotesIf you install the camera unit on a ceiling, take adequate waterproofing measures to prevent water seepage into the stand.When installing the unit on a wall, make sure the water drain is not sealed.
Notes on waterproofing of cable connection area
Despite the fact that this unit is rated IP66, the cables and/or the connectors join to the outside are not waterproof. To prevent water ingress from the cables and/or the connectors, waterproof them with the supplied waterproof tape as follows. Otherwise, there may be a risk of water entering through the cables and/or the connectors and shorting the unit or the connectors.
1 Connect the LAN cable and the ground wire.
2 To obtain optimal waterproofing, tear off the liner before wrapping,
then stretch the tape to twice its original length.If it is not fully stretched, the waterproofing function of the tape can not be achieved.
3 Overlap the tape at least half of its width when wrapping.
NotesDo not press the network cable tab down when wrapping it.
Make sure at least 10 mm (
/2 inches) of the wire part is wrapped.
4 After wrapping, squeeze the tape with your fingers at the overlapping
parts so that layers are airtight and fully adhered.(continued overleaf)Unit: mm (inches)
Sony SNC-EB632R

Got a question?

Number of questions: 0

Do you have a question about the Sony SNC-EB632R or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Sony SNC-EB632R owners to properly answer your question.

View the manual for the Sony SNC-EB632R here, for free. This user manual comes under the category Security cameras and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Sony SNC-EB632R? Ask your question here

Sony SNC-EB632R specifications

Brand Sony
Model SNC-EB632R
Product Security camera
EAN 4905524962451
Language English
Filetype PDF
Type IP security camera
Placement supported Outdoor
Day/night mode
Remote viewing
Connectivity technology Wired
Form factor Bullet
Product colour Black,White
Mounting type Ceiling/wall
International Protection (IP) code IP66
Maximum resolution 1920 x 1080 pixels
Video compression formats H.264,M-JPEG
Supported graphics resolutions 320 x 180,352 x 288,640 x 360,640 x 480 (VGA),704 x 576,720 x 480,720 x 576,1024 x 576 (WSVGA),1280 x 720 (HD 720),1920 x 1080 (HD 1080)
Analog signal format system NTSC,PAL
Gain control type Auto
Frame rate 30 fps
Total megapixels 2.14 MP
Privacy masking
Image stabilizer
Minimum illumination 0 lx
Viewing angle, horizontal 105.3 °
Viewing angle, vertical 56.9 °
White balance ATW,Fluorescent,Indoor,One push,Outdoor
Camera shutter type Electronic
Camera shutter speed 1/1 - 1/10.000 s
Image sensor
Sensor type CMOS
Optical sensor size 1/2.9 "
Lens system
Zoom capability
Optical zoom 3 x
Digital zoom 4 x
Focal length range 3 - 9 mm
Maximum aperture number 1.2
Video motion detection
Active tampering alarm
Intelligent Video Surveillance (IVS) system features Face detection
Built-in HDD
Night vision
Night vision
Night vision distance 30 m
LED type IR
Number of illumination LEDs 20
Infra-red wavelength 850 nm
Ethernet LAN
Ethernet interface type Fast Ethernet
Cabling technology 10/100Base-T(X)
Supported network protocols Pv4, TCP, UDP, ARP, ICMP, IGMP, HTTP, DHCP, DNS, NTP, RTP/RTCP, RTSP, SMTP, IPv6, HTTPS, SNMP
Quality of Service (QoS) support
Number of users 20 user(s)
Ports & interfaces
Ethernet LAN (RJ-45) ports 1
Interface RJ-45
Signal-to-Noise Ratio (SNR) 50 dB
Weight & dimensions
Width 93 mm
Depth 93 mm
Height 160.9 mm
Width (with stand) 140 mm
Depth (with stand) 140 mm
Height (with stand) 313.4 mm
Packaging content
Number of cameras 1
Resource CD
System requirements
Windows operating systems supported Windows 7 Professional x64,Windows 7 Ultimate x64,Windows 8 Pro x64,Windows 8.1 Pro x64
Minimum processor Intel Corei7 2.8 GHz
Minimum RAM 2000 MB
Power over Ethernet (PoE)
Power consumption (typical) 11 W
Power source type PoE
Management features
Web-based management
Operational conditions
Operating temperature (T-T) -30 - 50 °C
Storage temperature (T-T) -20 - 60 °C
Operating relative humidity (H-H) 20 - 90 %
Storage relative humidity (H-H) 20 - 95 %
show more

Frequently asked questions

Below, you will find the most frequently asked questions about the Sony SNC-EB632R.

Is your question not listed? Ask your question here