When power is supplied by IEEE802.3at (PoE+) equipment, if the switch is set to
PoE, the range of activation and operating temperature is limited. When power is
supplied by IEEE802.3af (PoE) equipment, if the switch is set to PoE+, the camera
will not work properly.
When power is supplied from the AC or DC source and if the switch is set to PoE,
the heater will not work. Note that if you use the camera in a low temperature,
the camera may not work.
To reset the camera to the factory default settings, hold down this switch with a
point and supply the power to the camera.
MONITOR output jack
Connect this jack to a video input connector of a video monitor. You can adjust
the camera or lens while looking at the image on the video monitor. After
adjusting the camera or lens, disconnect the cable.
Use this switch to adjust lens’ zoom and focus. Slide the switch lever to select the
[W] WIDE: Zoom out
[T] TELE: Zoom in
[N] NEAR: Focus on a nearby subject
[F] FAR: Focus on a distant subject
Hold down the center of the ZOOM/FOCUS switch for a moment to focus
SD card slot
This slot is used for optional SD memory cards.
Image data in the camera can be recorded to a memory card by inserting it into
Gently insert an SD card in (see illustration) until it clicks into place.
This unit is only compatible with SD and SDHC memory cards.
For inquiries regarding verified SD memory cards, contact your authorized Sony
Base screw (two positions)
Shows the name of this camera and its electric rating.
When installing the unit on a wall, make sure this water drain is not sealed.
If you attach the camera in the height such as the wall or the ceiling, etc.,
entrust the installation to an experienced contractor or installer.
If you install the camera at a height, ensure that the installation location and
its material are strong enough to withstand a weight of 15 kg (33 lb 11 oz) or
more, and then install the camera securely. If the ceiling is not strong enough,
the camera may fall and cause serious injury.
Do not pull on any cables forcefully, as a connection may become loose.
To prevent the camera from falling, make sure to attach the supplied wire rope.
If you attach the camera to the ceiling, check periodically, at least once a year,
to ensure that the connection has not loosened. If conditions warrant, make
this periodic check more frequently.
Deciding the Installation Location of the Camera
After deciding the direction in which the camera will shoot, make the required hole
(ø40 mm (1
inches)) for the connecting cables using the supplied template.
Then decide the four mounting hole positions to install the base stand.
The camera stand is provided with four ø4.5 mm (
/16 inches) mounting holes.
Install the camera stand on a ceiling or wall with screws through four mounting
holes: The required mounting screws differ depending on the installation
location and its material. (Mounting screws are not supplied.)
Steel wall or ceiling: Use M4 bolts and nuts.
Wooden wall or ceiling: Use M4 tapping screws. The panel thickness must be
15 mm (
/8 inches) or more.
Concrete wall: Use anchors, bolts and plugs suitable for concrete walls.
Junction box: Use screws to match the holes on the junction box.
The required mounting screws differ depending on the installation location and
its material. If you do not secure the camera with the appropriate mounting
screws, the camera may fall off.
Installing the Camera
Pass the cables through the hole for connecting cables made at the
2 Fix the wire rope to the wall or ceiling.
3 Install the camera on the wall or ceiling.
The remaining cable can be incorporated in the space between the base
stand and the mounting surface. (
Insert the four screws in the screw holes on the camera stand, and then
tighten the screws to attach the camera.
When installing the camera on the wall, be sure the TOP mark on the camera
stand is at the top.
Refer to “Mounting screws” in section D for screw to be used.
If you install the camera unit on a ceiling, take adequate waterproofing ˎ
measures to prevent water seepage into the stand.
When installing the unit on a wall, make sure the water drain is not sealed. ˎ
Notes on waterproofing of cable connection area
Despite the fact that this unit is rated IP66, the cables and/or the connectors
join to the outside are not waterproof. To prevent water ingress from the cables
and/or the connectors, waterproof them with the supplied waterproof tape as
follows. Otherwise, there may be a risk of water entering through the cables
and/or the connectors and shorting the unit or the connectors.
1 Connect all the required cables and the ground wire.
2 To obtain optimal waterproofing, tear off the liner before wrapping,
then stretch the tape to twice its original length. (
If it is not fully stretched, the waterproofing function of the tape can not be
3 Overlap the tape at least half of its width when wrapping. (-2)
Do not press the network cable tab down when wrapping it.
When you wrap the power input cable, start from the heat shrinkable tube.
Make sure at least 30 mm (1
/4 inches) of the wire part that is connected to
the power supply equipment is wrapped. (2-c)
Since the connector of the power input cable has gaps, wrap the connector
Make sure at least 10 mm (
/2 inches) of the wire part (excluding the power
input cable) is wrapped.
Make sure there is no unwrapped part or damage on the tape.
4 After wrapping, squeeze the tape with your fingers at the overlapping
parts so that layers are airtight and fully adhered.
Unit: mm (inches)
Got a question?
Number of questions: 0
Do you have a question about the Sony SNC-VB632D or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Sony SNC-VB632D owners to properly answer your question.
About the Sony SNC-VB632D
View the manual for the Sony SNC-VB632D here, for free. This user manual comes under the category Security cameras and has been rated by 1 people with an average of a 8.7. This manual is available in the following languages: English. Do you have a question about the Sony SNC-VB632D? Ask your question here