Targus PA095 manual

Targus PA095
(1)
  • Number of pages: 2
  • Filetype: PDF
  • Quick Start

    mobile

    docking station

    with ethernet

    USB 2.0

    Product Registration
    Targus recommends that you register your Targus accessory shortly after purchasing it. To register your Targus accessory, go to: http://www.targus.com/registration.asp
    You will need to provide your full name, email address, phone number, and company information (if applicable).
    Warranty
    Targus warrants this product to be free from defects in materials and workmanship for one year. If your Targus accessory is found to be defective within that time, we will promptly repair or
    replace it. This warranty does not cover accidental damage, wear and tear, or consequential or incidental loss. Under no conditions isTargus liable for loss of, or damage to a computer; nor
    loss of, or damage to, programs, records, or data; nor any consequential or incidental damages, even if Targus has been informed of their possibility. This warranty does not affect your
    statutory rights.
    Regulatory Compliance
    This device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) This device may notcause harmful interference, and (2) This device must accept
    any interference received, including interference that may cause undesired operation.
    FCC Statement
    Tested to Comply
    This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection
    against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the
    instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause
    harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
    the following measures:
    • Reorient or relocate the receiving antenna;
    • Increase the separation between the equipment and receiver;
    • Connect the equipment into an outlet on a circuit different from that to which
    the receiver is connected;
    • Consult the dealer or an experienced radio/TV technician for help;
    Changes or modifications not authorized by the party responsible for compliance could void the user’s
    authority to operate this product.
    Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
    All trademarks and registered trademarks are the property of their respective owners. Features and specifications are subject to change without notice.
    All rights reserved. © 2007, Targus Group International, Inc. and Targus, Inc. PA095U / 410-0210-001B
    Introduction
    Congratulations on your purchase of the Targus Mobile Docking Station with Ethernet USB
    2.0. This ultra portable expansion moduie directly connects to a desktop or notebook computer
    via a Universal Serial Bus (USB) port.
    Package Contents
    In addition to this user’s guide, the package contains:
    Targus Mobile Docking Station with Ethernet USB 2.0
    • CD-ROM Driver
    • AC power adapter
    NOTE: THE SUPPLIED AC POWER ADAPTER IS A UNIVERSAL ADAPTER THAT YOU CAN USE IN A 100 TO 240 AC VOLT OUTLET.
    System Requirements
    • USB 2.0 compliant port (When connected to a USB v1.1 upstream port,
    the Mobile Docking Station with Ethernet USB 2.0 will be less than
    optimal. For best results, connect it to a USB 2.0 port)
    Windows
    ®
    2000/XP/Vista™ operating system
    WARNING: YOU MUST INSTALL THE MOBILE DOCKING STATION’S SOFTWARE BEFORE CONNECTING IT TO YOUR COMPUTER. OTHERWISE, THE MOBILE
    DOCKING STATION WILL NOT WORK PROPERLY.
    Side View
    Back View
    Push Out
    Bottom View
    Connecting to the Mobile Docking Station
    Installing the Mobile Docking Station Drivers
    1. Turn on your computer.
    2. Insert the driver software CD into your computer’s CD-ROM drive.
    3. If setup does not begin automatically, click Start, Run, Then enter D:\Setup.exe (where D: is the path of your CD-ROM drive) and then click OK. The
    Welcome Screen appears.
    4. Click Next.
    5. If you are running the Windows
    ®
    XP operating system, the Important Information screen appears. Click Next.
    The Setup program begins installing the software driver.
    The Setup Complete Screen appears.
    6. Click Finish.
    7. Restart your computer.
    Connecting the Mobile Docking Station to Your Computer
    After installing the mobile docking station drivers, you are ready to connect the mobile docking station to your computer. To do this:
    1. Open the USB cable compartment, located on the bottom of the mobile docking station, and uncoil the cable.
    2. Connect the supplied AC power adapter to the DC jack on the mobile docking station, and the AC power plug to the wall outlet.
    3. Plug the USB connector end of the USB cable into the USB port of your computer.
    The following will configure automatically:
    • Ethernet 10/100 • Serial Interface Controller • USB Device (twice)
    • Parallel Interface Controller • PS/2 Adapter (twice)
    This configuration process takes a few minutes. The operating system does not prompt when configuration is complete. Watch that all hardware
    devices are configured before opening another application or connecting devices to the mobile docking station.
    Open
    USB connect to computer
    Hub Link
    Tx/Rx
    100M
    Serial
    PS/2(1) PS/2(2) USB(1)
    USB(2)
    Top Front View
    NOTE: SOME HARDWARE DEVICES MAY PROMPT YOU FOR THE LOCATION OF DEVICE DRIVERS.
    To install the drivers:
    1. Select “Install the software automatically (Recommended)” and click Next.
    The Found New Hardware Wizard program begins installing the hardware drivers.
    The Completing the Found New Hardware Wizard screen appears.
    2. Click Finish and repeat as needed for each device.
    3. Restart your computer.
    When your computer restarts, the mobile docking station should be completely configured.
    DC PS/2
    keyboard
    PS/2
    mouse
    RS232
    Parallel
    RJ-45
    ethernetSerialjack
    Network
    AC
    wall
    Mobile
    phone
    PDA
    Barcode
    Reader
Targus PA095

Got a question?

Number of questions: 0

Do you have a question about the Targus PA095 or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Targus PA095 owners to properly answer your question.

View the manual for the Targus PA095 here, for free. This user manual comes under the category Computer Accessories and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Targus PA095? Ask your question here

Targus PA095 specifications

General
Brand Targus
Model PA095
Product Computer accessory
Language English
Filetype PDF
Ports & interfaces
PS/2 ports quantity 2
Parallel ports quantity 1
USB 2.0 ports quantity 2
Other features
Interface USB
Compatible operating systems Windows 2000, XP
Dimensions (WxDxH) 23 x 171.5 x 57 mm
Network
Ethernet LAN (RJ-45) ports 1
Ethernet LAN
Performance
Product colour Black
Certification FCC, CE
show more

Frequently asked questions

Below, you will find the most frequently asked questions about the Targus PA095.

Is your question not listed? Ask your question here